Port St. John is a city where most of the electrical calls we get come from residential properties: homeowners dealing with a breaker that will not stay reset, landlords preparing a rental unit before a new tenant moves in, and property managers handling the kind of fault that shows up without warning on a Friday afternoon. We handle all of it. From a single dead outlet to a full panel replacement, the work gets scoped on the call and priced before anything is scheduled.
Call (321) 599-3556 any day between 5:30 AM and 8:00 PM.
The housing stock in Port St. John spans several decades, and older homes here often carry the electrical fingerprints of the era they were built in: panels that were sized for smaller loads, circuits that were never designed for today's appliances, and wiring that has never been touched since the original installation. We work through all of that. Homeowners who have never called an electrician and property managers running multiple units both get the same process: describe the problem, get a price, book the visit.
Whether this is your first repair or your tenth, lighting questions tend to come in two flavors: something stopped working, or something needs to be added. Both are worth thinking through before the visit, because what gets done while we are already on site often costs less than a separate call later.
Inside, the work ranges from replacing a fixture that has failed to installing recessed lighting in a room that has never had it, wiring under-cabinet lights in a kitchen, or adding a dimmer where a standard switch used to be. A ceiling fan swap is a straightforward job when the wiring is already there. When it is not, we run what is needed.
Outside, security lighting, motion-activated floods, and general exterior fixtures all require circuits rated for outdoor use and GFCI protection at every exposed outlet. Coastal conditions in this part of Brevard County accelerate corrosion on hardware that was not specified for the environment, so the fixture and the wiring method both matter. If other outdoor work is already on the list, adding a lighting circuit at the same time is worth considering.
A Level 2 charger needs a dedicated 240-volt circuit, and the panel has to have the available capacity to carry it before that circuit can be run. In homes with older or smaller panels, a load calculation comes first. That tells us whether the panel can handle the added draw or whether an upgrade is the right starting point. We run the circuit, size the breaker correctly, and confirm the wiring meets the load the charger will put on it.
Swapping a fixture for a ceiling fan is simple when a rated ceiling box is already in place. When there is no box, or the existing one was not installed for a fan's weight and movement, we replace it before the fan goes up. For rooms with no overhead wiring at all, we run the circuit. A fan that wobbles or hums after installation is almost always a mounting problem, not the fan itself.
A detached garage or outbuilding that needs power requires its own circuit run from the main panel, sized for whatever the space will actually be used for. A workshop draws more than a storage shed with a single light. Electric gate operators need a dedicated circuit and, depending on the installation, a disconnect at the gate itself. We assess the run, the load, and the panel capacity before anything is installed.
A circuit that trips under load, an outlet that works most of the time, or a breaker that resets fine but fails again in a week are the jobs that take longer to scope because the fault does not announce itself. We trace the circuit, test the connections, and work back from the symptom. The fault is traced before anything is replaced, which keeps the repair focused on what is actually wrong.
Pricing for electrical work depends on what the job actually involves, and the only way to give an accurate number is to understand the scope. When you call, we go through what you are dealing with: a repair, a panel upgrade, a new circuit, a rewire, a generator hookup. The rate is based on that conversation.
What moves a quote is what the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change. A ceiling fan installation in a room with existing overhead wiring is a different job from the same fan in a room that has never had a ceiling fixture. A dedicated appliance circuit in a home with panel capacity available is a different job from the same circuit in a home that needs a service upgrade first.
The scope of the electrical work is priced before it starts. You get a number before anything is booked, and if the scope changes once we can see the wiring on site, we explain what changed before we proceed.
When a problem will not keep, the call still works the same way: describe what is happening, and we work out what the schedule allows. Burning smells near an outlet or panel, a breaker that will not reset, or a sudden loss of power to part of the house are situations we treat as urgent. Availability for a specific time is confirmed when you call.
For rental units and businesses that have to stay open, we work around what the property needs. A tenant who cannot be without power in part of the unit, or a commercial space that cannot shut down a circuit during business hours, is a scheduling conversation we have before the visit, not when we arrive. One call and we are on it.
Some electrical problems are straightforward to find because they are always present. Others are not. A circuit that only trips when the air conditioning and the range are running at the same time, a fault that appears when it rains and clears up when it dries, or an outlet that works for weeks and then fails without any obvious change are all problems where the symptom and the cause are separated by time or conditions.
Finding an intermittent fault is its own job. It requires testing the circuit under load, checking connections at every point along the run, and sometimes waiting for the conditions that produce the failure. We do not replace components to see if the problem goes away. The fault is traced before anything is touched, because a repair that addresses the wrong cause leaves the real one in place.
With a local company, a question about the work gets a straight answer.
When part of a home loses power and the breakers look fine, the fault may not be inside the house at all. The service entrance, the meter base, and the utility connection are the boundary between what we handle and what the utility company owns. We check the panel and the service-entrance equipment on our side of that line first.
If the fault turns out to sit on the utility's side, the next step is a call to the utility company rather than more work on the panel. We tell you what we found and what that means for who handles it from there. Where the meter base or service-entrance equipment on the customer's side needs work, that is part of what we do. Service-entrance and meter upgrades are a separate scope from a panel replacement, and we distinguish between them on the call.
We take calls from across Port St. John and the communities nearby. Sharpes, North Merritt Island, West Canaveral Groves, Titusville, and Cocoa are all covered, along with the broader stretch of Brevard County that connects them. If you are in the area and not sure whether your address falls within our range, call and ask.
We are available every day from 5:30 AM to 8:00 PM. The process is the same wherever the call comes from: describe the job, get a price, book the visit. How a job in Port St. John usually runs is walked through on our full list of electrical services.
A pre-sale inspection focuses on identifying existing issues that a buyer's inspection might flag, and repairs are typically targeted at bringing the property up to a baseline standard. A renovation for long-term use involves more planning around future load requirements and may include upgrades that go beyond what a sale requires. We discuss the goal on the call and scope the work accordingly.
A new addition needs circuits run from the panel to the new space, with the panel capacity checked first to confirm it can carry the added load. Depending on the size of the addition, a subpanel in the new space may be more practical than running individual circuits back to the main panel. We scope that on the call and explain the options.
The more specific you can be, the more useful the call is. Tell us where the symptom is happening, whether it started suddenly or gradually, whether it affects one outlet or an entire room, and whether anything changed around the time it began, such as a new appliance, a storm, or a breaker you reset. That detail helps us scope the job before we arrive.
The electrical side of a generator installation covers the transfer switch, the wiring between the generator and the panel, and confirming that the panel has the capacity to carry the standby load. The transfer switch is what isolates the home from the utility line while the generator runs, and it is required for the hookup to meet code. We handle that connection and the panel side of it.
Call (321) 599-3556 to go through what the job involves at your address.
Homes built in the 1960s and 1970s across Brevard County were wired for loads that bear little resemblance to what a modern household draws. Panels sized for that era, aluminum branch-circuit wiring at connection points, and two-prong ungrounded outlets are common findings in Port St. John's older residential stock. An electrical inspection goes through the panel, the circuits, and the visible wiring and explains what it finds before any work is recommended.
Ready for your wiring. Call now.
Reach us at (321) 599-3556 any day between 5:30 AM and 8:00 PM.
The price is confirmed before anything is scheduled, and the next step is nothing more complicated than picking up the phone.
Call Melbourne Electrical Company at (321) 599-3556 for a quote on any job in Port St. John or the surrounding area.
See our town-by-town list. Wiring and panel work nearby: Titusville, Cocoa, Cocoa West, Rockledge.
Port St. John's housing stock runs from mid-century homes with original fuse boxes to newer construction with modern load demands, and commercial properties that sit in a different category entirely. We work across all of it, from a single outlet that stopped working to a full panel upgrade ahead of storm season. Call us with what you are dealing with and we will scope the job on the phone, give you a price before anything is scheduled, and get the work done right. Below is a quick look at what we cover and what to expect from each service.
| Type of Work | What the Job Involves | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Surge and Lightning Protection |
| Any Port St. John home with electronics, major appliances, or exposure to frequent lightning activity | Florida leads the country in lightning strikes per square mile, and Port St. John sits in one of the most active corridors. A panel-level surge device catches voltage spikes before they reach the circuits inside the house. |
| Whole-Home Generator Installation |
| Port St. John homeowners preparing for hurricane season or frequent storm-related outages on the Space Coast | The transfer switch isolates the home from the utility line while the generator runs, which is a code requirement and a safety necessity. We handle the wiring and the switch, not the generator unit itself. |
| Electrical Panel and Service UpgradesMost Popular |
| Homes adding EV chargers, major appliances, or carrying older panels that cannot meet current demand | Air conditioning runs hard year-round in this area, and when you add a Level 2 charger or an electric range, the math on panel capacity changes fast. We run the load calculation first. |
Call us at (321) 599-3556, seven days a week from 5:30 AM to 8:00 PM, and we will go over what you are dealing with, scope the job, and give you a price before anything is booked.
(321) 599-3556