Most people assume a flickering outlet or a breaker that will not hold is a handyman call. It is not. The fault is usually inside the wiring, the breaker itself, or a connection point that has worked loose over years of heat cycling. Getting the symptom to stop means tracing the cause, and that is electrical work. We handle it for homes and rental properties throughout Vero Beach South, from a single dead outlet to a full panel replacement.
A city this size carries a wide range of housing, and the electrical work it produces reflects that. Older homes on original wiring sit alongside newer construction with modern load demands. Landlords managing rental units need code-compliant work documented properly. Homeowners adding an EV charger or a standby generator need a panel that can carry the new load. We take all of it.
Call (321) 599-3556 for a quote on any job, and we will go through it with you before anything is scheduled.
Some electrical problems will keep. A ceiling fan that wobbles, a switch that needs replacing, an outlet you have been meaning to add for months. Those get booked at a time that suits the household or the property schedule.
Others will not. A burning smell near a switch plate, a breaker that trips every time a particular circuit is used, an outlet that is warm to the touch. Those are not situations to leave overnight. We take short-notice calls and urgent work throughout Vero Beach South, and availability for a specific visit is confirmed when you call. We do not promise a window we cannot keep, but we tell you what the schedule allows when you reach us.
For rental properties and businesses that have to stay functional, we work around the situation. A tenant who cannot be without power to part of the unit, a small commercial space that needs to stay open during the repair. We scope what the job requires on the call and confirm what preparation, if any, is needed before we arrive.
When we finish a job, the work does not just stop at the last connection. The circuits we touch get tested. Breakers are labeled clearly. Any GFCI or AFCI protection that was installed or replaced is confirmed to be functioning. If the job involved panel work, the directory is updated to reflect what is actually on each breaker.
That documentation matters more than most homeowners realize until the property changes hands or a tenant raises a concern. A buyer's inspector who finds a panel with accurate labeling and a clear record of recent work reads the property differently than one who opens a box full of unlabeled breakers and guesses. We treat your home and its wiring the way we would our own, which means the finished job holds up to scrutiny.
An electrical safety inspection before a sale or a new tenancy is one of the more practical things a property owner can do. We go through the panel, the circuits, the outlets, and the visible wiring. We note what meets current code and what does not, and we explain the findings plainly before recommending any follow-on work.
Older homes in this part of Indian River County sometimes carry aluminum branch-circuit wiring or two-prong ungrounded outlets, both of which come up in buyer inspections and can delay a closing. Knowing what is there before the inspector arrives gives the seller options.
We also find panel work and circuit additions done by previous contractors or previous owners. Most of it is fine. Some of it is not. When we open a panel or trace a circuit and find wiring that does not meet code, we note what it is, explain what the risk is, and give you a price to correct it before we proceed. We do not make a drama of it. We tell you what we found and what it takes to bring it up to standard.
The price for electrical work depends on what the job actually involves, and the honest answer is that it cannot be set until the scope is clear. A repair call where the fault turns out to be a single loose connection costs differently from one where the fault traces back to a failing breaker or a section of wiring that has to be replaced. A panel upgrade sized for a current load costs differently from one that also needs to accommodate a new EV charger circuit.
What we can tell you is that the scope of the electrical work is priced before it starts. You get a number on the call, based on what you describe, and that number is confirmed once we can see the work on site. If the scope changes when we open the wall or the panel, we explain what changed and what it means for the cost before we continue.
Three things move a quote in either direction: what the fault turns out to be once it is traced, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change without additional work. We explain all three when they apply.
Call (321) 599-3556 and ask what the job covers.
Not all of it has to come out. The answer depends on what the wiring is, what condition it is in, and what it is being asked to carry.
Knob-and-tube wiring from an earlier era is not automatically a tear-out, but it has real limitations. It was not designed for grounded circuits, and adding load to it without understanding what it connects to is how problems start. Where it is intact and not carrying more than it was designed for, we note it. Where it is in poor condition or being asked to support a modern load, we explain the rewiring options.
Aluminum branch-circuit wiring is a different situation. The wiring itself is not the primary concern. The connection points are, because aluminum and copper expand and contract at different rates and can loosen over time. Aluminum-wiring remediation addresses those points specifically, which is often a more targeted fix than a full rewire.
Unpermitted additions are assessed the same way. We look at what was done, whether it meets current code, and what it would take to bring it up to standard. Some of it needs to come out. Some of it needs a correction at the connection or the panel. We tell you which before we start.
This area generates a consistent range of electrical jobs, shaped by the housing stock and by what the regional climate puts on a home's electrical system year-round. The work below covers what we handle regularly here.
An intermittent fault is the most frustrating kind because it does not always show itself when you want it to. A breaker that trips on a hot afternoon but holds all morning, an outlet that works most of the time, a light that flickers only under certain conditions. We trace these through the circuit, testing arc-fault and ground-fault breakers, checking connection points, and working back from the symptom to the source. The fault traced before anything is replaced keeps the repair accurate and avoids replacing parts that were not the problem.
Year-round air conditioning puts a sustained load on a panel that seasonal climates do not. When a home adds an EV charger, a standby generator hookup, or a new appliance circuit on top of that baseline load, the panel has to have the capacity to carry it. An EV charger or a hot tub often means checking the panel first. If the existing service cannot carry the added demand, a service upgrade to a higher amperage is the right step before the new circuit is run. We do the load calculation, confirm what the panel needs to handle, and scope the upgrade before any new circuit work is scheduled.
An inspection covers the panel, the branch circuits, the outlets, and the visible wiring. We check for arc-fault and ground-fault protection where code requires it, note the condition of the service entrance, and flag anything that does not meet current standards. The report is written down and explained before any follow-on work is recommended. For a home purchase, a rental property, or a home that has not had any electrical work done in years, an inspection is a practical place to start.
Low-voltage work covers the circuits and rough-in for doorbells, video doorbell systems, data drops, and similar installations. This category comes up during renovations, when a home office is being set up, or when a property is being prepared for a new tenant. The wiring side is what we handle. We run the circuit, confirm the supply is correct, and make sure the rough-in is ready for the device being installed.
We take calls from across Vero Beach South and the surrounding communities throughout Indian River County. Nearby areas we regularly cover include Vero Beach, Florida Ridge, West Vero Corridor, Gifford, and Lakewood Park. If you are in the area and not certain whether we cover your address, call and ask.
We are available every day from 5:30 AM to 8:00 PM. The scope and the price are settled on the call before anything is booked, so you are working with a real number before you commit to a visit.
One call. One electrician. One price, agreed first. What each job covers is written out on our electrical repair services page.
Yes. Kitchens and bathrooms have specific code requirements for circuit counts, GFCI protection, and dedicated circuits for certain appliances that do not apply to general living spaces. We address those requirements as part of the rewire rather than treating them as standard rooms.
Rental properties tend to accumulate deferred maintenance on the electrical side, particularly on outlets, switches, and breakers that have been in use for years without attention. GFCI protection in kitchens and bathrooms is a common gap in older units, and panel labeling is frequently incomplete or inaccurate after years of tenant turnover. We handle all of it, and we document what was done so the property owner has a clear record for the next inspection or lease renewal.
Mixed-era wiring is common in properties that have been added to or partially updated over time. We identify what is present, note where different generations of wiring connect, and explain what the situation requires. In some cases a targeted upgrade is enough. In others, the inconsistency is significant enough that a more complete approach makes sense.
Homes built in earlier decades were wired for the loads of that era, which were considerably lower than what a modern household draws. Air conditioning that runs year-round, a home office, a charging station for an electric vehicle, or a new large appliance can push an older panel past what it was designed to handle. We check the panel capacity before running any new circuit, and if an upgrade is needed, we scope that work and price it before anything else is scheduled.
The Southeast Florida region sees some of the highest lightning frequency in the country, and a nearby strike traveling through the power lines can damage appliances, electronics, and the panel itself in a single event. Whole-home surge protection installs at the panel and intercepts voltage spikes before they reach the circuits inside the house. Proper grounding and bonding work alongside it. For a home in this area with sensitive electronics or expensive appliances, panel-level surge protection is practical rather than precautionary.
Call (321) 599-3556 and ask what that installation involves for your specific panel.
Temporary outdoor circuits can be set up for an event with enough notice to plan the work. We confirm what the load requirements are, where the power needs to reach, and whether the existing panel can carry it before scheduling anything.
When you call, we ask what you are dealing with, where the symptom is showing up, and whether anything changed around the time it started. By the end of that conversation, you know what the job is likely to involve, what it will cost, and what happens next.
Call Melbourne Electrical Company at (321) 599-3556 any day between 5:30 AM and 8:00 PM.
Power restored. Code-compliant. Done right.
Take a look at our town-by-town list. Also serving the towns around: Sebastian, Micco, Grant-Valkaria, Malabar, Palm Bay.
Vero Beach South's housing stock runs from mid-century homes with original fuse boxes to newer construction with modern load demands, and commercial properties that sit in a different category entirely. We work across all of it, from a single outlet that stopped working to a full panel upgrade ahead of storm season. Call us with what you are dealing with and we will scope the job on the phone, give you a price before anything is scheduled, and get the work done right. Below is a quick look at what we cover and what to expect from each service.
| Type of Work | What the Job Involves | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Lighting Installation |
| Homeowners upgrading interior lighting, adding outdoor security lights, or replacing corroded exterior fixtures | Homes along the barrier island and coastal neighborhoods need fixtures rated for salt air. Standard hardware corrodes faster than most homeowners expect in this environment. |
| Electrical Panel and Service UpgradesMost Popular |
| Homes adding EV chargers, major appliances, or carrying older panels that cannot meet current demand | Air conditioning runs hard year-round in this area, and when you add a Level 2 charger or an electric range, the math on panel capacity changes fast. We run the load calculation first. |
| Wiring and Circuit Installation |
| Older homes with wiring that cannot safely carry current loads, or any property adding new living or working space | Aluminum branch-circuit wiring is a common finding in Indian River County homes built in certain decades. The risk concentrates at connection points, and we address those specifically. |
Call us at (321) 599-3556, seven days a week from 5:30 AM to 8:00 PM, and we will go over what you are dealing with, scope the job, and give you a price before anything is booked.
(321) 599-3556